|
|
VideoWaveVideoWave is available in 1.4GHz, 2.4GHz
and 5.8GHz versions,
approved for license-free use in the UK and internationally. It provides a
professional answer to wireless transmission of composite real time video
signals using proven video processing technology (PAL, SECAM and NTSC).
VideoWave can also be used in conjunction with our range of modems to offer
over air telemetry for full control of PTZ cameras.
 |
|
Download Brochure and Technical Specifications
(PDF file - 737KB) |
| |
|
Operation & Installation Guide - 1.4GHz
(PDF file - 342KB) |
| |
|
Operation & Installation Guide - 2.4GHz
(PDF file - 1.33MB) |
| |
|
Operation & Installation Guide - 5.8GHz
(PDF file - 1.06MB) |
APPLICATIONS:CCTV point-point, Air to Ground Link, Mobile
Surveillance, remote Site Monitoring, Covert. For a security application, click
here.
VTX1394S / VRX1394S (1.4GHz)
The 1.4GHz VideoWave units have been designed specifically for the UK
market where this frequency is available license-free at an output of 500mW.
Other countries may allow its use but usually at reduced power.
The units are small and light, housed in a very robust aluminium extrusion.
IP67 rated enclosures giving full weatherproofing for exposed locations are
also available. VideoWave may be used with the supplied patch antenna
or with externally mounted antennas for greater distances.
For other countries, the units are also available in the following frequencies:
1244MHz, 1274MHz, 1304MHz, 1364MHz, 1424MHz and 1454MHz.
- 500mW output power
- Lightweight robust design
- Signal strength indicator
- 12V operation
- Optional weatherproof enclosures (See below)
- Compliant with R&TTE Directive
- Tested to MPT 1349
- Size: 125 x 64 x 30mm
|
|
 |
VTX1394SE / VRX1394SE in Weatherproof Housing
 |
|
The Transmitter or Receiver unit is available in an IP67 weatherproof
housing for convenient outdoor use. It is supplied with an integral mains
power supply and an SMA antenna connector on the top. Cable glands are
provided in the base for video and power connections. Brackets are
supplied for mounting on a standard 50mm diameter pole.
- Weatherproof to IP67
- Mounts on standard 50mm pole
- Integral mains supply
- Various antennas available
- Size: 230 x 88 x 80mm
|
| |
|
1394MHz TX/RX in IP67 Enclosure (PDF - 208KB)
|
Top of page
VTX2400S / VRX2400S ( 2.4GHz)
The 2.4GHz VideoWave has been designed to meet the specifications for
license free use throughout Europe. Because of the varying regulations in
different countries, it is available with output powers between 10mW and
500mW (factory set).
The units are housed in a very robust aluminium extrusion. IP67 rated
enclosures giving full weatherproofing for exposed locations are also
available. VideoWave may be used with the supplied patch antenna
or with externally mounted antennas for greater distances.
 |
|
- 10mW to 500mW output power
- 3 channel switchable
- Lightweight robust design
- Signal strength indicator
- 12V operation
- Optional weatherproof enclosures (See below)
- Compliant with R&TTE Directive
- Tested to ETS 300 440
|
|
The 2.4GHz VideoWave can operate on any one of 3 channels, i.e. 2413MHz,
2442MHz or 2471MHZ. This allows the use of up to 3 cameras on a
single installation.
VTX2400SE / VRX2400SE in Weatherproof Housing
| The Transmitter or Receiver unit is available in an IP67
weatherproof housing for convenient outdoor use. It is supplied with an
integral mains power supply, a TNC antenna connector on the top, and an
'N' type antenna connector on the base for an external antenna. Cable
glands are provided in the base for video and power connections. |
|
 |
|
|
|
| |
|
2400MHz TX/RX in IP67 Enclosure (PDF - 1095KB)
|
Top of page
VTX5800S / VRX5800S ( 5.8GHz)
The 5.8 GHz VideoWave has been designed to meet the specifications for license free operation throughout Europe. The output power is 10mW or 25mW e.i.r.p. with the supplied patch antenna, which is within the limits for most of Europe.
The units are housed in a robust IP67 polycarbonate weatherproof housing, suitable for external use. VideoWave may be used with the supplied patch antenna or with externally mounted antennas for greater distances.
|
|
|
- 10mW (25mW eirp with supplied patch)
- 6 channel switchable (3 non-interfering)
- Lightweight robust design
- Signal strength indicator
- 12V operation
- Compliant with R&TTE Directive
Tested to ETS 300-440
|
The 5.8 GHz VideoWave can operate on any one of 3 non-interfering channels, which allows the operation of up to 3 cameras on a single installation. It is possible with the correct separation between antennas, where site conditions allow, to use all 6 available channels.
| |
|
VTX5800S/VRX5800S Data Sheet (PDF - 200KB)
|
VTX5800SE / VRX5800SE ( 5.8GHz)
- 10mW (25mW eirp with supplied patch)
- 6 channel switchable (3 non-interfering)
- Lightweight robust design
- Signal strength indicator
- 240Vac operation
- Compliant with R&TTE Directive
Tested to ETS 300-440
The Transmitter or Receiver unit is available in an IP67 weatherproof housing for convenient outdoor use. It is supplied with an integral mains power supply, a SMA antenna connector on the top, with cable glands in the base for video and power connections. |
|
 |
| |
|
VTX5800SE/VRX5800SE Data Sheet (PDF - 215KB)
|
VTX5801S / VRX5801S ( 5.8GHz)
VTX5801SE / VRX5801SE ( 5.8GHz)
The 5801 versions have the same specification as above, but have an additional alarm (digital switching) channel and an audio channel.
The inputs for the digital alarm channels on the transmitter are volt free contacts. On the receiver there are corresponding changeover relay outputs with contact rating 1A @ 30V dc.
The audio input on the transmitter is 1 V p-p into 100K ohms unbalanced. The receiver output is 1 V p-p (for a 1 V p-p input) with a frequency response of 50Hz to 15KHz.
Note that the audio channel can be linked out and used as a second digital alarm channel. This is link selectable.
Top of page
|
Video and Data for Radio Telemetry
For applications using PTZ cameras, RDT offer the addition of a
Radio Modem for complete control of the telemetry functions. This
allows the use of all pan and tilt functions as well as zoom, pre-sets
etc. from most of the commercially available video control systems. They are available stand alone (see modem page
in the products section) or housed in an enclosure together with a video
unit.
For compatibility with various makes of camera and controller, contact
RDT or see the 'Video Telemetry Compatibility' section on the
'Download' page.
|
|
 |
|
The IP67 weatherproof enclosures house a Video Transmitter (or
Receiver), a Radio Modem and power supply. They are complete with
antenna connectors for mounting the 1/2 wave whip antenna and patch directly to
the top of the enclosure. |
Part numbers are as follows:
| VTX1394SED-XXX * |
VideoWave Transmitter with Radio Modem |
| VRX1394SED-XXX * |
VideoWave Receiver with Radio Modem |
| Size: |
280 x 190 x 130mm |
| |
|
| VTX2400SED-XXX * |
VideoWave Transmitter with Radio Modem |
| VRX2400SED-XXX * |
VideoWave Receiver with Radio Modem |
| Size: |
280 x 280 x 130mm |
| |
|
| VTX5800SED-XXX * |
VideoWave Transmitter with Radio Modem |
| VRX5800SED-XXX * |
VideoWave Receiver with Radio Modem |
| Size: |
255 x 180 x 75mm |
| |
|
| VTX5801SED-XXX * |
VideoWave Transmitter with Radio Modem |
| VRX5801SED-XXX * |
VideoWave Receiver with Radio Modem |
| Size: |
255 x 180 x 75mm |
* Where XXX is the modem frequency (MHz) i.e. VTX1394SED-460 for UK
| |
|
1394MHz TX/RX & Radio Modem in IP67 Enclosure (PDF - 265KB)
|
| |
|
2400MHz TX/RX & Radio Modem in IP67 Enclosure (PDF - 796KB)
|
| |
|
5800MHz TX/RX & Radio Modem in IP67 Enclosure (PDF - 506KB)
|
|
Top of page
Four Camera System
Using the QL4000 Quad unit, it is possible to set up a system with 4 cameras transmitted over a single radio link, either 1.4 GHz, 2.4
GHz or 5.8GHz. The QL4000TXE combines the 4 video streams from the cameras and sends a single composite video over the air.
The quad image can be displayed and recorded as shown below.
The QL4000 is housed in an IP67 weatherproof housing for external use. It can be installed with the transmitter mounted as shown in the picture to give increased height to the transmitting antenna.
Cable entry glands are provided in the base of the enclosure for video input and power leads.
|
|
 |
| |
|
Download Videowave Quadlink (PDF file - 658KB)
|
Viewing a Quad Image
In this option, the video from the Receiver is fed directly to a monitor and/or VCR for display and recording. The image displayed and recorded will be a quad image.
Top of page
Survey Kit / Covert Operation
RDT can supply a complete portable video transmitter and receiver, with
batteries and an LCD monitor housed in a convenient robust carrying case.
The kit has a variety of uses particularly for covert operations or
temporary installations, but one of its main applications is for carrying
out a survey prior to installation.
Using the kit, a camera (not supplied) and battery operated transmitter can
be placed in the desired location. The receiving unit and LCD monitor can
then be used to check reception at the required destination. This can help
save wasted and sometimes costly installation time.
|
|
- Portable Transmitter and Receiver
- Available in 1.4GHz, 2.4GHz or 5.8GHz
- 4 inch LCD colour monitor
- Re-chargeable batteries
- Battery charger / power supply
- Mounting brackets
- Whip antennas
- Lockable flight case
Note: Camera not supplied
|
Top of page
|
Antennas
A selection of antennas is available suitable for most
applications depending on location and required coverage range.
The distances achieved vary greatly with each installation, the
surrounding terrain, buildings etc. so the figures quoted below
are a general guide and assume a reasonably clear 'line of sight'
between transmitting and receiving antenna.
1.4GHz
| Antenna
Type |
500mW output |
| ANT0002 |
1/2 Wave Whip (TNC Connector) |
750m - 1500m |
| ANT0003 |
1/2 Wave Whip (SMA Connector) |
750m - 1500m |
| ANT0004 |
Magnetic Mount |
750m |
| ANT0005 |
Dipole |
1 - 2km |
| ANT2350 |
3dB Patch |
1 - 2km |
| ANT2351 |
12dB Patch |
2 - 3km |
|
2.4GHz
| Antenna Type |
10mW |
25mW |
500mW |
| ANT2400 |
1/2 Wave Whip (TNC Connector) |
500m |
600m |
700m |
| ANT1251 |
1/2 Wave Whip (SMA Connector) |
500m |
600m |
700m |
| ANT0025 |
Dipole |
600m |
800m |
1000m |
| ANT2373 |
3dB Patch |
600m |
800m |
1000m |
| ANT2374 |
12dB Patch |
900m |
1100m |
1400m |
| ANT0026 |
Corner Reflector (14dB gain) |
1000m |
1200m |
1500m |
5.8GHz
| Antenna
Type |
Range |
| ANT5803 |
Whip, Omni-directional |
500m |
| ANT5805 |
5dB gain Patch (supplied as standard) |
1Km |
| ANT5805-CAB |
5dB gain Patch with 1.5mtr cable and mounting clips |
1Km |
| ANT5808-CAB |
8dB gain Dipole, omni-directional with 1.5mtr cable |
1Km |
| ANT5810-CAB |
10dB gain Panel with 1.5mtr cable |
1.4Km |
| ANT5820-CAB |
20dB gain Panel with 1.5mtr cable |
3Km |
| ANT5828-CAB |
28dB gain Parabolic Dish with 1.5mtr cable |
4Km |
Top of page
Contact RADIO DATA TECHNOLOGY LIMITED for:
Wireless Data Transmission, Radio Modems, Wireless Video, Radio Telemetry,
SCADA, Modbus, Wireless CCTV, Profibus, GSM Telemetry, monitoring, remote control,
Public Utilities, Transport, Traffic, Parking, Industrial Automation,
Security, Process Control, Data Acquisition, Remote Control, Signs, Flow
Control, Level Monitoring, Alarms, Access Control.
|
|
|
|
